A chandelier is one of the hardest things in a home to move. It is wired into the building. It is made of dozens or hundreds of parts that swing, chip, and tangle. And it does not sit flat on anything.
Most damage happens in two places: during the takedown, and inside a box that was never built for the shape. Both are avoidable. This guide covers the whole job in order, from who may disconnect the fixture in New York City to what the new ceiling needs before it goes back up.
The Short Answer
Photograph and label everything. Turn the power off at the breaker. Have a licensed electrician disconnect the fixture while someone supports its weight. Remove the bulbs, shades, and crystals and pack them separately. Then pack the frame so it cannot swing or rest on its arms.
| Question | Short Answer |
|---|---|
| Can I take it with me? | Check your sale contract or lease first. Attached light fixtures usually stay with a sold home unless the contract excludes them. |
| Who disconnects and reconnects it? | A licensed electrician. In NYC, replacing a fixture is licensed work that needs a permit. |
| Best packing for a valuable fixture? | A custom foam-lined crate or a hanging crate. |
| What must the new ceiling have? | Support rated for the weight. Over 50 pounds, the fixture needs support independent of the box unless the box is listed for the weight. |
| Is basic mover coverage enough? | No. Released value pays 60 cents per pound, and chandeliers are light for their value. |
First: Does the Chandelier Go With You?
Sort this out before anyone climbs a ladder.
If you are selling. Items attached to the walls, floor, or ceiling are generally treated as fixtures, and fixtures normally go to the buyer. As one New York real estate law firm puts it, chandeliers, wall sconces and other lighting fixtures are expected to remain after closing. If you want to keep yours, it has to be excluded in the contract of sale. The contract controls, not the listing. Tell your attorney or agent early.
If you are renting. A chandelier you bought and hung yourself is usually yours to take, but your lease may say how alterations and fixtures are handled. Read it and ask the landlord in writing before removal.
This is general information, not legal advice. Your contract or lease decides it.
How to Take a Chandelier Down, Step by Step
1. Photograph and Label Everything
Do this while the fixture is still hanging. Take wide shots from several sides, then close-ups of each tier, each arm, and how the crystals are strung. Guidance on glass chandeliers in the Journal of the American Institute for Conservation calls good photographs and sketches essential for careful reassembly. Number the arms with paper string tags.
2. Turn the Power Off at the Breaker
The wall switch is not enough. Turn off the circuit at the panel and confirm the fixture is dead before anyone touches it.
3. Have a Licensed Electrician Disconnect It
In New York City, this is not a do-it-yourself step. The Department of Buildings says no installation or modification to any electrical system can be performed without a permit. It lists replacing fixtures in existing outlets as minor electrical work that still requires a NYC Licensed Master Electrician and an electrical permit. Owners and workers can face violations and fines for unpermitted electrical work.
So the electrician disconnects the wiring. The movers support the fixture, take it down, pack it, and transport it. Schedule both for the same visit.
4. Support the Weight During Takedown
A chandelier should never hang from its wires or be lowered by one person on a ladder. The conservation guidance is blunt: this work always requires more than one person, and the greatest threat to a hanging chandelier is contact with the stepladder. For a large fixture, a professional crew uses a lift or scaffold platform so the weight is carried from below the whole time.
5. Remove Bulbs, Shades, and Crystals
Strip the fixture while it is still hanging if you can.
- Work from the outside in and from the bottom up. That is the order conservators recommend.
- Do not spin the fixture to reach the far side. Rotating can unscrew a chandelier from its hanging hardware. Walk around it.
- Keep sets together. Remove each strand of crystals whole. Label it by tier and position, then bag it on its own.
- Wrap each loose piece. Shades, bobeches, and glass cups each get their own wrap and go into a divided box.
- Do not straighten old pins. On antique fixtures, the pins that link the drops become brittle with age. Bending them usually snaps them.
6. Wrap the Arms and Pack the Frame
If the arms are designed to come off, remove them, tag them, and wrap each one. If they are fixed, wrap each arm in tissue and foam, then pad the spaces between arms so nothing can flex. No weight should ever rest on an arm, a glass canopy, or a finial.
Chandelier Packing Options Compared
The right container depends on the size, the value, and how far it is going.
| Option | How It Works | Best For | Limits |
|---|---|---|---|
| Original box | Factory foam cut to the exact fixture | Newer fixtures, if you kept all the inserts | Useless without the inserts |
| Double box with suspension | Wrapped frame centered in an inner box, cushioned on all sides inside a larger box | Small, sturdy fixtures on a short local move | Not for fragile glass or long hauls |
| Hanging crate or travel frame | The fixture hangs from a crossbar inside a rigid frame, as it does from a ceiling | Multi-arm and tiered fixtures that cannot rest on anything | Needs height and bracing so the fixture cannot swing |
| Custom foam-lined crate | Plywood shell with foam cut to the fixture and its parts | High-value, antique, or blown glass fixtures, long distance, storage | Costs more and takes time to build |
For a valuable fixture, a crate is the answer. We explain how crates are built in what gets crated and why. Our custom crating service builds them to the piece.
Different Chandeliers, Different Risks
Crystal chandeliers. The frame is usually sturdy. The risk is in the hundreds of drops and the pins that hold them. Labeling by tier is most of the job.
Murano and blown glass. Here the arms, leaves, and flowers are the glass. Every element comes off, gets numbered, and is wrapped on its own. This type should be crated.
Antique and gas-converted fixtures. Many old chandeliers were built for candles or gas and wired later. Conservators note that substandard wiring is common in electrified chandeliers, so have the electrician check it before it goes back up. Treat the finish like any other antique. Our guide to moving antique furniture without damage covers finishes and hardware, and our antique furniture movers handle period pieces.
Modern LED and sputnik designs. Sputnik fixtures have long, thin arms that bend at the joint. Remove the arms if they unscrew. Many LED fixtures have built-in light sources and a separate driver, so the electronics need padding too.
Oversized lobby, stairwell, and ballroom fixtures. These are rigging jobs. A crew works from lifts or scaffolding, takes the fixture apart in sections, and crates each section on site. The photo at the top of this post shows that kind of job.
Loading and Transport
A chandelier travels the way it hangs: upright. A hanging crate stays vertical and is strapped to the truck wall so it cannot tip. Foam-lined crates travel in the orientation marked on the outside. Nothing gets stacked on top, and every container is labeled with its contents and which way is up.
Rehanging at the New Place
The Ceiling Box Has to Be Rated for the Weight
This is the part people skip. Under National Electrical Code section 314.27(A)(2), a standard ceiling outlet box for lighting can support a fixture of up to 50 pounds unless the box is listed for the fixture's actual weight. A heavier fixture has to be supported independently of the box, which usually means bracing tied into the building structure.
The NYC Electrical Code is based on the 2020 National Electrical Code with city amendments, so your electrician will apply the local version. Weigh the chandelier, tell the electrician the number, and have the box and support confirmed before installation day. The chain matters too. Conservators say it should be closed-link steel or brass and able to hold more than the full weight of the chandelier.
Plaster Ceilings and Medallions
Prewar apartments and brownstones often have plaster ceilings and decorative medallions. Plaster cannot carry a fixture. The support has to reach the structure above it. A medallion is decoration, not a mount. If the fixture is heavy, the electrician may need to open the ceiling to add support. Plan for that before move day.
Hanging Height
There is no code rule for this, only convention. Over a dining table, lighting retailers commonly suggest the bottom of the fixture sit 30 to 36 inches above the tabletop, a little higher with taller ceilings. Measure the new ceiling before you move. A chain that suited a tall prewar ceiling may be too long for the new room, and shortening the chain and wiring is work for the electrician.
Reconnection and Reassembly
A licensed electrician makes the connection. The movers or installers lift and hold the fixture, then redress it from your photos and labels. Our installation service covers placement and hanging support, working alongside your electrician.
Clean It Before the Crystals Go Back On
The crystals are already off, so this is the easiest time to clean them. Crystal maker Schonbek recommends hand-washing removed crystal in lukewarm water with mild detergent, then rinsing and drying with a soft cloth. It warns against cleaners that contain ammonia. For antique or gilded fixtures, ask a conservator before using any cleaner on the metal.
NYC Building Logistics
A crated chandelier is much bigger than the chandelier. That changes the building plan.
- Measure the elevator. A hanging crate is tall and cannot be tipped. Check the cab height, depth, and door opening before the crate is built.
- Send the COI early. Most managed buildings require a certificate of insurance from the mover, and many want one from the electrician too. See our COI guide.
- Book the working hours. Buildings set their own hours for moves and for contractor work. The takedown involves both, so confirm the window with the managing agent and reserve the service elevator.
Valuation and Insurance
This is where chandeliers get people.
On an interstate move, federal rules require movers to offer two levels of liability. The free one is released value. Under it, the mover is responsible for no more than 60 cents per pound per article. Compensation is based on weight, not value.
Run the math. A 40-pound crystal fixture would be covered for $24. What to do instead:
- Choose Full Value Protection on an interstate move. The mover must then repair, replace, or pay for a damaged item.
- List the chandelier in writing. Under Full Value Protection, movers can limit liability for items worth more than $100 per pound unless you list them on the shipping documents.
- Let the movers pack it. The FMCSA notes that claims are harder to prove for boxes you packed yourself.
- Call your own insurer. Ask whether your policy covers the fixture in transit and in storage.
Moves within New York State follow state rules, so read the valuation section of your paperwork either way. Our guide to moving insurance in NYC explains each option.
Storing a Chandelier
If the new ceiling is not ready, the chandelier may sit for weeks or months. Conservators say a chandelier headed for storage should be labeled, completely disassembled, and properly packed. Leave it in its crate, upright, with nothing stacked on top. Keep the crystals, hardware, and photos with the frame. Choose clean, dry storage.
Frequently Asked Questions
Do I need an electrician to take down a chandelier in NYC?
Yes. The Department of Buildings requires electrical work to be done under a permit, and it lists replacing fixtures in existing outlets as work that needs a NYC Licensed Master Electrician. Movers handle the support, packing, and transport.
How do you pack a chandelier for moving?
Remove the bulbs, shades, and crystals. Label each strand by tier and bag it separately. Wrap each arm. Then pack the frame so no weight rests on the arms: in its original box with inserts, double boxed for a small sturdy fixture, or in a hanging or foam-lined crate for anything valuable.
How much does it cost to move a chandelier?
It depends on the fixture, so we do not publish a flat price. The main drivers are size and weight, how much disassembly it needs, whether a custom crate is built, access for the takedown, and building rules at both ends. The electrician bills separately. Send photos and dimensions and ask for a free quote.
How much weight can a ceiling box hold?
Under the National Electrical Code, a standard ceiling box for lighting can support a fixture of up to 50 pounds. A heavier chandelier needs support independent of the box, unless the box is listed for that weight. Your electrician should confirm what is in your ceiling.
Do chandeliers stay with the house when you sell?
Usually, yes, unless the contract of sale excludes them. If you plan to take yours, have your attorney write the exclusion into the contract.
The Bottom Line
Moving a chandelier is three jobs: electrical work that belongs to a licensed electrician, careful disassembly and packing, and a rehang that starts with a ceiling box and support rated for the weight.
Settle ownership before you touch it. Book the electrician and the movers for the same visit. Measure the elevator and the new ceiling. And do not rely on 60 cents per pound to protect something that light and that valuable.
Have a chandelier that needs to come down, travel, and go back up in one piece? Avant-Garde Moving offers custom crating for fragile pieces and plans the move around your electrician and your building. Send us photos and dimensions when you request your free quote.

